short answer
A hardware hackathon asks you to build a working physical device, which MLH describes as a 24 to 36 hour event built on microcontrollers, sensors and actuators. Parts come from your bag or a shared lab with limited stock, so bring your own board, USB data cables and a government photo ID for checkout. Pick a scope you can demo in about three minutes and record a video the first time it works.
hardware hackathonson this page
How a hardware track differs
The difference is parts. A software team can code from minute one; a hardware team first has to get the right board, sensors and cables from a supply that runs out.
MLH still sends hardware labs to some of its member events, where hackers borrow Arduinos, Raspberry Pis, webcams and Grove sensor kits for the weekend. Its published lab list shows how thin the stock is: 9 Raspberry Pi 4B kits and 12 Arduinos with base shields per lab, with counts subject to change and different contents in EU and APAC labs. MLH's organizer guide tells events to hold an ID until every item comes back.
Some makeathons ration parts with a budget. MakeUofT 2025 limited teams to 2 to 4 people because of finite hardware and gave each team 300 credits: a microcontroller cost about 100, a peripheral 20 to 25, a dongle about 5. One board ate a third of the budget.
Expect a rule about what counts as hardware. MakeUofT requires a physical device that is at least electrically powered or computer programmed. Browse current events on the hardware hackathons board.
What to bring, and what to leave home
Pack as if the parts desk will be empty when you reach it.
- Government-issued photo ID. MakeUofT 2025 required it to sign out components.
- Your own microcontroller, a USB data cable that fits it, a breadboard and jumper wires. MLH's guide says bringing your own electronics cuts reliance on the lab.
- A laptop and chargers, with the Arduino IDE and board drivers installed at home. MLH asks events to have hackers pre-download drivers and IDEs to spare the venue Wi-Fi.
- A phone hotspot. MLH warns organizers that standard university networks often block IoT devices, which can strand an ESP32 demo.
- Fuses, if you plan to work with mains power. MakeOHI/O 2026 asked mains and high-voltage builders to bring their own.
MLH also suggests soldering headers onto your microcontrollers before the event. Some events ban any preparation (Monash's HARDHACK 2021 barred software or hardware prepared before the start), so ask first.
Leave behind what the rules exclude. MakeUofT 2025 welcomed personal components but not a pre-assembled project. HARDHACK 2021 banned personal 3D printers. MakeOHI/O 2026 prohibited railguns, coil guns, other weapons and induction furnaces. If your build needs a lithium battery pack, ask the organizers before you bring it.
Pick a scope that demos in 3 minutes
Your demo slot is short. MakeOHI/O 2026 judged a 3-minute video followed by 6 minutes of questions, and MakeUofT 2025 gave each team about 5 minutes to present and demo. Plan backward from that.
Aim for one sensor, one decision and one visible result: the board reads something, decides, and a motor moves or a light changes. If a judge cannot see the result from across the table, add a screen or a sound.
Budget time for the physical side. MLH's guide gives a sample 24-hour split of 10% ideation, 35% development, 30% packaging and 25% documentation, and recommends around 30% of project time for physical packaging such as printing and fitting.
Treat 3D printing as a queue. MakeUofT 2025 accepted only functional prints, capped at 5 hours and 18 x 18 x 18 cm, and closed print submissions at 5 pm on day one. For the talk itself, the hackathon demo guide covers the script.
Arduino, ESP32 or Raspberry Pi
Pick the smallest board that does the job.
- Arduino: the simplest path for sensors, buttons and motors. The UNO R4 WiFi runs at 5 V and adds an ESP32-S3 module for Wi-Fi and Bluetooth. MLH tells anyone borrowing an Arduino from its lab to install the Arduino IDE first.
- ESP32: Espressif's Wi-Fi and Bluetooth chip, a good pick when the device has to talk to a phone or a web API.
- Raspberry Pi: a full computer running Raspberry Pi OS, which is based on Debian. Choose it for a camera, computer vision, a desktop screen or heavy Python libraries.
Check voltages before you wire. Raspberry Pi's documentation says its GPIO pins run at 3.3 V, are not 5 V tolerant, and can be permanently damaged by 5 V. If you need both worlds, let a laptop or Pi do the heavy compute and a microcontroller handle the sensors over USB serial.
Have a fallback before you need it
MLH's guide notes that projects get tested for durability when they are moved for judging. Plan the fallback in the first hours, not the last.
- Record a video the first time it works. MLH tells teams to take photos and videos of the project working as a backup for judging. MakeOHI/O 2026 judged a pre-submitted 3-minute MP4, capped at 500 MB.
- Write a reset checklist: the steps to bring the build back after a power loss or a move. MLH recommends one.
- Build on a tray or board you can carry, as MLH suggests, so you never rewire at the judging table.
- Keep a simulator copy. Wokwi is a browser electronics simulator, free for personal use, with Wi-Fi simulation. Its supported list covers microcontrollers (Arduino Uno, Nano and Mega, the ESP32 family, STM32 and Raspberry Pi Pico) but not a Linux Raspberry Pi. If a part dies, a Wokwi copy can still show your firmware logic.
How hardware gets judged
Read the rubric before you choose parts. Two of the three below score a working device directly.
MakeUofT 2025 scored overall winners on idea originality, technical complexity, working demonstration and presentation.
MakeOHI/O 2026 scored six criteria from 1 to 5: innovation, creativity, communication, project development, impact, and how the team handled failures and pivots. Its judges asked about technical implementation, challenges, future improvements and impact, and scored only work done during the event.
Monash's HARDHACK 2021 even counted cost of materials, next to innovation and originality, functionality and value to society.
Two habits follow. Keep a parts list with rough prices, and be ready to say what you built at the event versus what you brought. For more on rubrics, see hackathon judging criteria.
Safety rules are real rules
Organizers can stop your project. MakeOHI/O 2026 reserved the right to shut down any project it considered unsafe, and discouraged high-voltage builds such as Tesla coils, Jacob's ladders and plasma speakers.
- Shop tools are supervised. At Ohio State's Bolz Makerspace, 3D printers, soldering stations and laser cutters could be used only with a full-time staff member present. MakeUofT 2025 required a signed waiver for its fabrication space.
- Borrowed parts must come back intact. HARDHACK 2021 made participants pay for hardware returned with permanent modifications such as soldering.
- Ask before you plug anything into mains, and keep hot tools off shared tables.
India: the SIH hardware edition
In India, the Smart India Hackathon runs a hardware edition. Its FAQ says SIH started in 2017 with software only and added the hardware chapter in 2018.
Teams have six members including at least one woman, all from the same institute, and the hardware edition encourages mixed teams of mechanical and electronics engineers, product designers and programmers. The FAQ lists INR 1.5 lakh as the winning prize for both hardware and software. See the Smart India Hackathon guide for the full process.
FAQ
What should I bring to a hardware hackathon?
A government photo ID for parts checkout, your own microcontroller with a matching USB data cable, a breadboard and jumper wires, and a laptop with the Arduino IDE and drivers already installed. Check the event's rules before bringing batteries, mains-powered gear or a 3D printer.
Do hardware hackathons provide the hardware?
Many do. MLH lends Arduinos, Raspberry Pis and sensors at some member events, and MakeUofT runs its own signout site, but stock is limited, so bring a board of your own if you have one.
Arduino or Raspberry Pi for a hackathon?
Use an Arduino or ESP32 for sensors, motors and simple wireless links. Use a Raspberry Pi when you need a full Linux computer for a camera, vision or heavy Python, and remember its GPIO pins are 3.3 V only.
Can beginners join a hardware hackathon?
Yes. MakeUofT describes itself as for everyone from beginners to veterans, with industry mentors on hand. Pick a small project with one sensor and one output.
What if my hardware breaks before judging?
Show the backup video you recorded when it first worked, and a simulator copy if you made one. MakeOHI/O 2026 judged a pre-submitted 3-minute video, so record early.
sources
- MLH hardware lab resources mlh.com
- MLH hardware lab contents guide.mlh.com
- MLH organizer guide: hardware guide.mlh.com
- MLH: why hardware hackathons guide.mlh.com
- MLH: hardware hackathon pitfalls guide.mlh.com
- MLH: hardware hackathon challenges guide.mlh.com
- MLH: hardware environment requirements guide.mlh.com
- MakeUofT 2025 participant package docs.google.com
- MakeUofT FAQ makeuoft.ca
- MakeOHI/O 2026 hack.osu.edu
- MakeOHI/O 2026 participant judging guide docs.google.com
- HARDHACK 2021 rules (Monash) hardhack.monash.edu
- Wokwi docs docs.wokwi.com
- Wokwi supported hardware docs.wokwi.com
- Arduino UNO R4 WiFi docs.arduino.cc
- Espressif ESP32 espressif.com
- Raspberry Pi hardware documentation raspberrypi.com
- Raspberry Pi OS documentation raspberrypi.com
- Smart India Hackathon FAQ sih.gov.in
Checked against these pages when published. Rules and dates change, and the organizer's own page is the authority. Spotted an error? Send a correction.